Meters and More

Meters for Utility & Industrial Power Testing

ABB/Hitachi CB-2000

Battery powered, no need for a mains connection
Approximately 8 h operating time between charges
Easy analysis and generation of reports with supplied software
Clear LCD display easy to read in daylight or dark environments
Measuring range of 0 to 1000 μF

AEMC BR07

Rotary Switch Selector
Stop Position To Prevent Accidental Switching From 10 To 0
Seven Decades: 1 To 10MΩ
Max Current: 0.1mA
Male Ground (Earth) Terminal With Safety Jack
Outputs On Ø 4mm Safety Terminals
Ground Jumper Lead EN 61010-2-031, 150V Cat. II Pollution Degree 2
Accuracy 1%

Easy-Laser XT660

Align the machine
Check base twist
Check bearing play
Check soft foot
Document and share the results

Emerson TREX

Enables HART or Fieldbus module communications
Configure and test valves inline
Configure and test instruments inline
Touchscreen display is easy to use with bulky work gloves

EXTECH 380400

1 To 11,111,110 Ohm, 1 Ohm Per Step
Wattage : 1W
Slide Switches That Allow The User To Simply Add Or Subtract For Desired Value
With Seven Decades Of Resistance
ABS Plastic Housing Case, Rugged Components

FLUKE 1587

Safety first. Connect the insulation tester then keep yourself out of harm's way by monitoring your test measurements remotely
Prove your job is done right by quickly seeing and sharing insulation resistance test results wirelessly with your smartphone
Quickly find problems by saving and comparing measurements over time on a wireless device

FLUKE 190-204

200 MHz Bandwidth Model
Deep Memory: 10,000 Samples Per Channel Waveform Capture So You Can Zoom In On The Details
Dedicated 5000 Count Digital Multimeter
Connect-And-View Continuous Auto-Trigger, Single Shot, Pulse Width, And Video Triggering
ScopeRecord Roll Mode, Capture Waveform Sample Data For Up To 48 Hours
TrendPlot, Trend Measurement Readings For Up To 22 Days
Advanced Automatic Measurements, Power (Vpwm, VA, W, PF) And Time (MAs, V/S, W/S)
IP-51 Rated For Dust And Drip Proof To Withstand Harsh Environments

FLUKE 289

True RMS Datalogging Multimeter
AC Bandwidth Specified To 100 KHz
Min/Max/Avg And Peak Capture
Low Impedance Voltage Function
AC/DC Voltage Range: 50.000 MV To 1000.0 V
AC/DC Current Range: 500.00 ΜA To 10.000 A
Resistance Range: 500.00 Ω To 500.0 MΩ
Capacitance Range: 1.000 NF To 100 MF
Frequency Range: 99.999 Hz To 999.99 KHz

FLUKE 376

True RMS Datalogging Multimeter
AC Bandwidth Specified To 100 KHz
Min/Max/Avg And Peak Capture
Low Impedance Voltage Function
AC/DC Voltage Range: 50.000 MV To 1000.0 V
AC/DC Current Range: 500.00 ΜA To 10.000 A
Resistance Range: 500.00 Ω To 500.0 MΩ
Capacitance Range: 1.000 NF To 100 MF
Frequency Range: 99.999 Hz To 999.99 KHz

FLUKE 725

Calibration Of Both Temperature And Pressure Transmitters
Measure/Source/Simulate MA Loop Parameters
Measure And Source MA, Volts DC, Frequency, And Resistance
Built-In 24 V Loop Power Supply
Store And Recall Frequently Used Calibration Set Ups

FLUKE 789

Compact Digital Multimeter And MA Loop Calibrator Solution
Full-Featured MA Loop Calibrator With Built-In 24v Loop Power
Quickly And Easily Troubleshoot Every Part Of A Control Loop
Large, Bright Dual-Measurement Display

FLUKE 9040

Indication Of Field Rotation In Three-Phase Networks
Fast, Clear Indication
Clear, LCD Screen
Fused Test Leads
Three Crocodile Clips And Three Test Probes

Fluke 754

Handles fast pulsed RTD transmitters and PLCs, with pulses as short as 1 ms
Measures/sources pressure using any of 29 Fluke 700Pxx Pressure Modules
Creates and runs automated as-found/as-left procedures to satisfy quality programs or regulations, and records and documents results
Holds up to a full week of downloaded procedures and calibration results
Uses many features like autostep, custom units, user-entered values during test, one-point and two-point switch testing, square root DP flow testing, programmable measurement delay and more
Provides easy-to-use multi-lingual interface
Features a bright white dual display for reading both sourced and measured parameters simultaneously

Fluke 805 FC

Reliable, repeatable, accurate device for checking bearings and overall vibration
Features innovative sensor design that minimizes measurement variations caused by device angle or contact pressure
Provides consistent data quality at both low and high frequency ranges
Offers four-level severity scale to assess urgency of problems and bearing condition
Measures overall vibration (10 Hz to 1,000 Hz) for acceleration, velocity, and displacement units of measurement for a wide variety of machines
Provides Crest Factor+ technology for reliable bearing assessment using direct sensor tip measurements between 4,000 Hz and 20,000 Hz
Compares vibration levels with ISO-10816 severity scales and stores results to the Fluke Connect Cloud
Features colored lighting system (green, red) and on-screen comments to indicate how much pressure needs to be applied to take measurements

Fluke 820

High intensity 7-LED array-4,800 Lux @ 6,000 FPM/30cm
High efficiency LED solid-state light source with uniform flash characteristics allow for higher flash rates-30-300,000 FPM (flashes per minute)
Digital pulse width modulation for exceptionally sharp images at high speeds
Rugged, durable design utilizes solid-state LEDs with no filaments, gases, hollow cavities, or glass (one meter drop)
Quartz-accuracy control system provides high accuracy-0.02 % (± 1 digit)
Multi-line LCD display

SOLMETRIC PVA-1500

Measures And Displays I-V And P-V Curves And Key Parameter Values
Advance Dbuilt-In PV Models Provide Immediate PV Performance Checking
Accurately Measures High-Efficiency Modules And Strings.
Database Of More Than 70,000 Modules, With Automatic Updates

Shimpo DT-205LR

Outstanding Accuracy allows usage in the strictest applications
Sophisticated laser beam detection to 20 feet provides operator safety during testing
Exceptionally rugged die-cast aluminum housing enables usage in the harshest conditions
Wide field selection of units in both instantaneous rate as well as totalized length satisfies a multitude of user requirements
Large 5 digit display aids user visibility
10 measurement memory capacity allows quick retrieval of stored data plus additional last, max. & min. values
Long-life battery (25-40 hrs. continuous use) eliminates concerns of being down during testing

Request Quote

Lets us help you find the right equipment for the job.

Thank you! Your submission has been received!

Oops! Something went wrong while submitting the form.

Visit Us

Come by the office anytime during working hours.